Top 24 for Best Hadco Lighting 2019

 

Hadco Lighting 1010-H Hadco Lighting 1010-H Beacon Bronze,120V 120V - Â  Lower housing may be recessed directly in the ground or in concrete. Metal halide ballasts are capable of starting at -20° f or -30° c and hps at -40°f or -40°c. Ballast is factory wired and tested.   Fully gasketed top and bottom. Ballasts are factory pre-wired and tested. Optical assembly clear borosilicate glass refractor lens. Check with local authorities before specifying alternate voltages.   Beacons are partially recessed. Ballast all hid ballasts are core and coil and regulated with power factors better than 90% (hpf). Fluorescent ballast is capable of starting at 0° f or -18° c.   Fasteners are 300 series stainless steel.   Laboratory tested for superior weatherability and fade resistance in accordance with astm b117 specifications. Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation. Installation & mounting voltage caution some local interpretation of the nec section 210-6 only permit the use of 120 volt fixtures when they are mounted below 8′.   Removable roof for easy relamping. Potting compound must be used to seal the conduit wire entry. Lamping 100w maximum a19 lamp.   Molded silicone gasket seals glass, top and bottom, and prevents moisture intrusion into the fixture. 13w fluorescent socket is a gx23/gx23-2.   Note the base has two (2) ½” npt conduit entrances for connection to the power source.   Fluorescent ballast is core and coil, npf class b. Finish thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Hid is 4kv rated medium base porcelain socket with nickel-plated screw shell and center contact. Electrical assembly incandescent is medium base porcelain socket with nickel-plated screw shell and center contact.   Housing die-cast aluminum. Note all ballasts are eisa / title 20 / title 24 compliant where applicable.

 

Hadco Lighting Rll1-a Rec Louver Steplyte, Black - Weight 1. 2 lb. Low voltage quick connector, catalog #lvc3 included for easy hook-up to the low voltage supply cable, not included. Certifications manufactured to iso 90012008 standards. Pigtail of 18-2 awg, 105° c, spt-1w wire. Housing die-cast aluminum faceplate with galvanized steel, single gang recessed box with stainless steel fasteners. Height 2 13/16″ (71mm) width 4 5/8″ (116mm) depth 2 3/4″ (70mm) max. 12 volt fixture is pre-wired with 6-ft. Electrical assembly single contact bayonet (s-8). Gasketing is diecut neoprene. Warranty three-year limited warranty. Laboratory tested for superior weatherability and fade resistance in accordance with astm b117 specifications. 12 volt system requires remote transformer, not included. Lamp is included with fixture. Optical assembly frosted tempered glass lens. Finish thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Lamping 12w maximum s-8 (93) lamp.

 

Hadco Lighting Ig3h Ig3h Rock Guard With Lens For Il336 Well Light 120v Fiberglass Reinforrced Polyester Composite - Fiberglass reinforrced polyester composite rockguard with tempered clear glass lens fasteners are stainless steel accessory attaches with set screws to the top of the il336-al and il336-a inground fixtures 6″ (152mm) dia x 1 11/16″ (43mm) tall. 120v.

 

Hadco Lighting MUL4_AS7 MUL4 Small Mushroom Pathlyte Low Voltage Black - The mul4 pathlyte assembly runs on the lower voltage of 12 v and is safety-certified for use in wet locations. The mul4 mushroom is a path light mostly installed outdoors, hence the roof is made from stainless steel to protect it from the elements. The mul4 small mushroom low voltage pathlyte from hadco lighting has a stem which is about 19. A spun aluminium reflector amply reflects the downcast light of the 20 watts lamp. Hadco lighting offers these path lighting fixtures in a variety of finishes — speckled stone, brass, bronze, verde, sienna, black and natural cast bronze. 5â€ù long and a dome 5 1/16â€ù in diameter. A powder coated finish further protects the fixture from losing its luster due to rain or sun.

 

Hadco Lighting B1-a B1 Small Aluminum Bullyte Black Without Shroud 100w Par/r20 - Black without shroud. 100w par/r20.

 

Hadco Lighting CB100AK5812 CB100 Composite Bricklyte Black 12V 2 x 18W 1141 (Lamp Type Included) - . The cb100 has die-cast aluminium box with a slight proportion of copper to prevent corrosion and enable it to function even in wet locations. Hadco from the house of philips brings its over five decade expertise in the lighting industry into play in the cb100 composite bricklyte. With a height of 90 mm and depth of 103 mm, the cb100 composite bricklyte can be set into brick and concrete structures and comes in a bronze finish. Its electronic ballast can start up even in -20o fahrenheit (thataâ’‰”¢s 52o below zero) and the powder coating is durable and suited for concrete and masonry application.

 

Hadco Lighting Tm2h Tm2 Tree Mount Junction Box Bronze - Bronze.

 

Hadco Lighting WAM1_H WAM1 Floodlyte standard Clear Lens 120V Bronze Clear Lens Clear Lens - Manufactured to iso 90012008 standards. Lamping 75w maximum t3 mini candelabra lamp. Fully-adjustable swivel arm with vibration-proof locking teeth. Fixture is pre-wired with 18 awg black, white, and ground wires. Fasteners are 300 series stainless steel. 75 lb. Finish thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Lower wattage lamps are acceptable. Height 4 7/8″ (123mm) width 6 7/8″ (175mm) length 5″ (126mm) max. S. Optical assembly clear tempered glass lens.  Housing die-cast aluminum. Lamp is not included. Certifications etl listed to u. ” Nps male threads to screw onto accessory mounting stake or junction box, sold separately. Frosted tempered glass lens. Weight 1. Gasketing is silicone. Warranty three-year limited warranty. Safety standards for wet locations. Cetl listed to canadian safety standards for wet locations. Electrical assembly mini-candelabra socket (e11).

 

Hadco Lighting B3-h B3 Aluminum Bullyte Line Voltage Accent Bronze 100w Par/r30 - Bronze. 100w par/r30.

 

Hadco Lighting TU3_G TU3-G Large Tulip Pathlyte Verde 120V 120V - 65 lb. Cetl listed to canadian safety standards for wet locations. Laboratory tested for superior weatherability and fade resistance in accordance with astm b117 specifications. Housing single-piece cast aluminum. Height 36″ (914mm) width 10 5/16″ (262mm) max. Lower wattage lamps are acceptable. Lamping 100w maximum a19 lamp. Safety standards for wet locations. Finish thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. 1/2″ nps male threads to screw onto accessory mounting stake or junction box, sold separately. Stem is extruded aluminum, sold separately. S. Warranty three-year limited warranty. Weight 3. Manufactured to iso 90012008 standards. Certifications etl listed to u. Fixture is pre-wired with 18 awg black, white, and ground wires. Electrical assembly 4kv rated porcelain mini-can base. Lamp is not included. Nickel-plated screw shell with center contact.

 

Hadco Lighting 150 Watt 12 Volt Transformer With Built In Timer And Photoeye-tc152-12tp - Warranty ten-year limited warranty.

 

Hadco Lighting Landscape Light Copper Pathlyte Replacement Cul4 Natural Copper Shade Only - Spun solid copper roof with copper stem machined brass threaded adapter for tool-less relamping. ½” Nps male threads to screw onto accessory mounting stake and junction box sold seperately. Natural copper is bright polished, untreated copper. Fixture sold seperately shade only 4″ wide. Color will age naturally to a fine dark copper patina.

 

Hadco Lighting Bi2 Bi2 Cast Iron Junction Box – 40605 Nps 120v Hot Dipped Galvanized Cast Iron Junction Box. 4 - 120v. Hot dipped galvanized cast iron junction box 4″ [102mm] square x 3″ high [76mm] with 1/2″ nps [13mm] top inlet two (2) 3/4″ npt [19mm] bottom inlets used with aluminum or composite fixtures.

 

Hadco Lighting 30" Aluminum Bollard 120 Volt Bronze Db30-h - Anchor rods internal (3) 3/8″ dia x 8″ long (1 cm x 20cm). Lamping incandescent medium base a19 (100 watt max).

 

Hadco Lighting RSCL2AK5812 RSCL2 Low Voltage Louvered Steplytes Black - Pigtail of 18-2 awg, 105 c, spt-1w wire. Warranty three-year limited warranty. Lamping two 18w maximum s-8 (1141) lamps (single contact bayonet base). 12 volt system requires remote transformer, not included. Cetl listed to canadian safety standards for wet locations. S. Cast bronze louver is natural cast bronze with frosted tempered glass. Die-cast aluminum trim contains less than 0. Certifications etl listed to u. Zinc-rich primer and thermoset powdercoat for durability. (Note flange not included with cb100 fixture. Thermal protection device is required for installations in drywall, plaster, wood or other non-masonry materials. Electrical assembly single contact bayonet (s-8). Height 3 1/2″ (89mm) width 9″ (229mm) depth 4 11/16″ (103mm) housing height 2 11/16″ (68mm) housing width 8 1/8″ (207mm) max. Ada compliant when used in indoor and outdoor wall applications. Low voltage quick connector, catalog #lvc3 included for easy hook-up to the low voltage supply cable, not included. Die-cast aluminum back box contains less than 0. Optical assembly horizontal louver lens made of die-cast copper-free aluminum with a 45 cutoff and frosted tempered glass. ). Lamp is included with fixture. Weight 3. 3% copper to resist corrosion. Safety standards for wet locations. 12 volt fixture is pre-wired with 6-ft. Finish thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. 86 lb. 3% copper to prevent corrosion in concrete or masonry applications. Faceplates are color-impregnated. Manufactured to iso 90012008 standards.  Housing aluminum parts have zinc-rich primer and thermoset powdercoat for durability.

 

Hadco Lighting BL5016-HS7BAB BL5016 Aluminum Accent Light Bronze 20W MR16 Lamp Type Included - The housing is constructed of double gasketed, die cast marine-grade alloy aluminum for long life. Hadco lighting promotes lights which are both decorative and functional and the bl5016 accent light is a prime example. The socket features a retention clip to secure the lamp in place. A 360 degree fully adjustable swivel arm allows for precise lighting along with an angled lens for self-cleaning. Hadco assures quality and longevity by providing even the nuts, bolts and fasteners in stainless steel to prevent rusting or corrosion when placed outdoors. The glass optical assembly is placed at a slight angle of about 10o to facilitate self-cleaning or simplify the lens cleaning process. With vibration-proof serrated teeth along with the base of the housing, it provides a positive lock. The bl5016 accent light from hadco lighting is a low voltage accent light which is mostly used outdoors and available in bronze, sienna, verde and black finishes. It uses 12 volts to power bulbs up to 50 watts and a fully rotatable shroud with a flexible swivel for perfect focus of light at the desired spot. The fixture is ul, cul listed for a 50 watt mr16 lamp. The five-stage powder-coating process ensures optimum outdoor lifespan even when exposed to the elements.

 

Hadco Lighting Waml1d Led Floodlyte Low Voltage - Replacement shade for cul2d. Shade only, stake and junction box sold seperately. Bronze. Natural copper is bright polished, untreated copper color will age naturally to a fine dark copper patina. Color will age naturally to a fine dark copper patina.

 

Hadco Lighting Rl4-as7 Rl4 Large Horizon Pathlyte 12v Black - The lens is made of spun aluminium and the fixture conforms to all building and regulatory and safety norms. With a height of 17 and a quarter inches, the rl4 large horizon pathlyte can be used from the curb or from a detached garage to the entrance, to provide illumination and safety and reduce the risk of stumbling in the dark. The rl4 large horizon pathlyte is a low voltage path lighting fixture from hadco lighting, consisting of a powder-coated, extruded aluminium stem and shade, covering a 20 watt bi-pin lamp. The stem is tested for weather- and fade-resistance. The intensity of attention to detail and safety can be seen in the fact that even the fasteners are made in stainless steel to withstand the rigors of the outdoors.

 

Hadco Lighting BU3-H BU3 Composite Bullyte Line Voltage Accent Bronze 75W PAR30 - . A porcelain base socket ensures electrical insulation and safety, even in wet conditions. The light assembly is housed in a polymer composite shroud and is capable of complete 360o horizontal and vertical rotation to give complete operational freedom when focusing the lights. Light from the lamp is dispersed through a clear tempered glass placed at an angle of 10o to facilitate easy cleaning. Hadco philips is the preferred lighting brand for residential, commercial, landscape and municipal users and the bu3 composite bullyte accent proves why. The bu3 composite bullyte line voltage accent from hadco lighting are accent lights available in verde, black and bronze finishes with a lamp capacity of up to 75 watts. With a length of 241 mm, the bu3 composite allows for ballast to be either in-ground or above ground.

 

Hadco Lighting Rl4 Large Horizon Pathlyte 12v, Stake Included - The intensity. The rl4 large horizon pathlyte is a low voltage path lighting fixture from hadco lighting, consisting of a powder-coated, extruded aluminium stem and shade, covering a 20 watt bi-pin lamp. The stem is tested for weather- and fade-resistance.

 

Hadco Lighting BU4-H BU4 100W Par38 Composite Bullyte Line Voltage Bronze - Cetl listed to canadian safety standards for wet locations. Optical assembly one-piece injection molded ultem high performance polymer with silicone o-ring gasket. 100w maximum mh medium base e17 100w maximum mh medium base par38 lamp is not included. Width 6 1/4″ (159mm) length 16 1/2″ (419mm) max. Warranty ten-year limited warranty. ” Nps male threads to screw onto accessory mounting stake or junction box, sold separately. Hid par30 mh or mv acceptable with remote ballast (not included). Manufactured to iso 90012008 standards. Bun4, buw4, shroud included. S. Lens is siliconed into shroud. One-piece injection molded ultem high performance polymer composite. Nickel-plated screw shell with center contact. Shroud is optional. Bu4, shroud optional. Fasteners are 300 series stainless steel. Fully-adjustable swivel arm with vibration-proof locking teeth. Lower wattage lamps are acceptable. Ballast must order inground (ibh) or above ground (abh) ballast housing separately. 75 lb. Finish composite is textured, pressure formed, molded-in-color. Weight 3. Certifications etl listed to u.  Housing fully rotatable shroud, gasketed, ultem high performance polymer composite. Gasketing is silicone. Safety standards for wet locations. Electrical assembly 4kv rated porcelain mini-can base. Lamping 100w maximum par30/r30 or par38/r40 medium base lamp.

 

Hadco Lighting Iul516-h Iul516 Bronze Micro Inground Low Voltage Lamp Type Not Included - 12v iul516 composite in-ground lightlamp type mr16socket base bi-pinrequires remote transformer (not included)finish brass.

 

Hadco Lighting FUL1_GS7 FUL1-G Small Floral Pathlyte Verde 12V – Mounting Stake Included 12V - 1 lb. Lamping27w maximum s-8 (1156) lamp. Safety standards for wet locations.   12 volt fixture is pre-wired with 3-ft pigtail of 18-2 awg, 105° c, spt-1w wire.   Manufactured to iso 90012008 standards. Electrical assemblysingle contact bayonet (s-8). Warrantythree-year limited warranty.   Stem is extruded aluminum, sold separately.   Laboratory tested for superior weatherability and fade resistance in accordance with astm b117 specifications.   Lower wattage lamps are acceptable.   12 volt system requires remote transformer, not included.   Lamp is included with fixture. Certificationsetl listed to u. S.   Cetl listed to canadian safety standards for wet locations. Weight2.  Housingsingle-piece cast aluminum.   1/2″ nps male threads to screw onto accessory mounting stake or junction box, sold separately. Finishthermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Height21 1/2″ (544mm)width8 1/4″ (209mm)max.   Low voltage quick connector, catalog #lvc3 included for easy hook-up to the low voltage supply cable, not included.

 

Hadco Lighting Landscape Light Replacement Shade For Cul2D Small Led Copper Pathlyte 12V - Replacement shade for cul2d. Color will age naturally to a fine dark copper patina. Shade only, stake and junction box sold seperately. 35″ w. Natural copper is bright polished, untreated copper color will age naturally to a fine dark copper patina.